Learning the Basics of Plumbing for Bathtub Installation
Learning the Basics of Plumbing for Bathtub Installation
Blog Article
They are making several great annotation on the subject of How to Install a Bathtub in general in this post on the next paragraphs.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Mounting a bath tub isn't specifically rocket science, but it does call for solid plumbing, carpentry, and often, tiling skills. Changing an old bathtub with a brand-new one is likewise a moderately difficult job. If the old bathtub is readily accessible, the task can relocate rapidly; if you need to open up a wall to eliminate the old tub and position the new bath tub, the task is a lot harder. In either instance, the project is within a home handyman's abilities, although you will certainly need a helper to leave the old bathtub and also set in the brand-new one. Make sure you have certified yourself for the task and also are comfortable trying it. Instead of employing a professional to take over a halfway-completed job, it is far better to take into consideration employing one prior to you begin. Opportunities are you might require an expert plumber to make tube connections.
This short article will assist you mount a brand-new tub in your restroom if you have actually already bought a new bathtub as well as don't need to alter the setup of your previous water supply pipelines.
Your tools and material list must comprise the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you ought to do is separate the supply of water. After doing so, turn on the taps to drain any water continuing to be in the system. The procedure of removing the existing faucets can be fairly problematic because of the restricted accessibility that is often the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the taps. Have a cloth ready for the staying water that will certainly come from the pipelines. Once the supply pipelines have actually been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will require to stop the single taps from transforming during this procedure. As soon as the faucets have been gotten rid of, the holes in the bath/basin will need to be cleansed of any type of old securing substance.
Before moving on to fit the brand-new faucets, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end offers a connection to the current supply pipes.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washing machines remain in place between the tap as well as the sink. Safeguard the faucet in position with the maker given backnut. As soon as the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular faucet adapters. The previous kind needs to be linked to the tap finishes first, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Tub
Making use of both wood boards under its feet, position the bath tub in the required setting. The wooden boards are practical in equally spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 tiny points.
The next goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the spirit level and also changing the feet on the tub up until the spirit level reads level.
To install taps, fit the bottom of the outermost flexible faucet connector to the appropriate supply pipe by making a compression sign up with; then do the same for the various other faucet.
Activate the water and inspect all joints and also brand-new pipework for leakages as well as tighten them if essential. Fill up the bath tub and additionally inspect the overflow outlet as well as the typical electrical outlet for leakages.
Finally, take care of the bathroom paneling as defined in the producer's user's manual. Tiling as well as sealing around the tub must wait until the bath tub has been utilized a minimum of once as this will settle it into its final placement.
Planning for the Installation
Firstly, the supporting structure supplied with the bathroom must be fitted (if called for) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make certain that if the tap features a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps unit to avoid pressure on the bathtub.
Fit the adaptable faucet connectors to the bottom of both taps making use of 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you utilize every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should currently be ready to be fitted in its final placement.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to fracture a rigid seal, causing the water to pass through the wall surface in between the bathroom and also the tiling, bring about problems with dampness and possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your components and also installations. They are offered in tubes as well as cartridges, and are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of soaked newspaper or soft rope. Remember to always load the bath tub with water before sealing, to allow for the activity experienced when the tub is in use. The sealer can crack rather very early if you do not consider this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally quickly readily available on the marketplace. It is advisable to fit the floor tiles utilizing waterproof or water resistant sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a reader on Installing A Bathtub, I thought sharing that excerpt was a good thing. In case you enjoyed reading our article if you please do not forget to share it. I enjoy reading our article about Installing A Bathtub.
Request our service. Report this page